what protocols are required to register a cisco 8800 series ip phone in cucm
Cisco IP Telephone Installation
Verify the Network Setup
Every bit they deploy a new IP telephony arrangement, system administrators and network administrators must complete several initial configuration tasks to ready the network for IP telephony service. For data and a checklist for setting up and configuring a Cisco IP telephony network, see the documentation for your item Cisco Unified Communications Manager release.
For the phone to operate successfully as an endpoint in your network, your network must meet specific requirements. Ane requirement is the appropriate bandwidth. The phones require more bandwidth than the recommended 32 kbps when they annals to Cisco Unified Communications Manager. Consider this higher bandwidth requirement when you configure your QoS bandwidth. For more information, refer to Cisco Collaboration System 12.ten Solution Reference Network Designs (SRND) or later ( https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/srnd/collab12/collab12.html ).
 Note | The telephone displays the engagement and fourth dimension from Cisco Unified Communications Managing director. The time displayed on the telephone can differ from the Cisco Unified Communications Managing director fourth dimension by up to 10 seconds. |
Procedure
| Footstep 1 | Configure a VoIP Network to run across the following requirements:
|
| Step 2 | Fix the network to support one of the following:
|
Activation Code Onboarding for On-bounds Phones
You tin can apply Activation Lawmaking Onboarding to quickly fix new phones without autoregistration. With this approach, you lot control the phone onboarding process using the one of the post-obit:
-
Cisco Unified Communications Majority Assistants Tool (BAT)
-
Cisco Unified Communications Director Administration interface
-
Administrative XML Web Service (AXL)
Enable this characteristic from the Device Information section of the Phone Configuration page. Select Crave Activation Code for Onboarding if you want this feature to apply to a single on-premises phone.
Users must enter an activation code earlier their phones tin can annals. Activation Lawmaking Onboarding tin can be practical to individual phones, a grouping of phones, or across an unabridged network.
This is an like shooting fish in a barrel way for users to onboard their phones because they only enter a 16-digit activation code. Codes are entered either manually or with a QR code if a phone has a video camera. We recommend that you use a secure method to give users this data. Just if a user is assigned to a phone, then this information is bachelor on the Cocky Care Portal. The audit log records when a user accesses the code from the portal.
Activation codes can merely be used one time, and they expire later on 1 week by default. If a code expires, yous will have to provide the user with a new i.
Y'all will observe this approach an easy style to keep your network secure because a phone cannot register until the Manufacturing Installed Certificate (MIC) and activation code are verified. This method is also a convenient way to bulk onboard phones because information technology doesn't employ the Tool for Machine-registered Phone Support (TAPS) or autoregistration. The rate of onboarding is one phone per second or nearly 3600 phones per 60 minutes. Phones tin be added with the Cisco Unified Communications Managing director Administrative, with Administrative XML Web Service (AXL), or with BAT.
Existing phones reset after they are configured for Activation Code Onboarding. They don't register until the activation lawmaking is entered and the phone MIC is verified. Inform current users that you are moving towards Activation Code Onboarding before you implement it.
For more information, see Administration Guide for Cisco Unified Communications Manager and IM and Presence Service, Release 12.0(i) or after.
Activation Code Onboarding and Mobile and Remote Access
You tin use Activation Code Onboarding with Mobile and Remote Access when deploying Cisco IP phones for remote users. This feature is a secure way to deploy off-premises phones when autoregistration is not required. Just yous tin can configure a phone for autoregistration when on-premises, and activation codes when off-bounds. This characteristic is similar to Activation Code Onboarding for on-premises phones, merely it makes activation code bachelor for off-premises phones as well.
Activation Code Onboarding for Mobile and Remote Access requires Cisco Unified Communications Manager 12.5(ane)SU1 or later on, and Cisco Expressway X12.v or later. Smart Licensing should be enabled also.
You enable this feature from the Cisco Unified Communications Manager Administration, but note the post-obit:
-
Enable this feature from the Device Information section of the Telephone Configuration page.
-
Select Require Activation Code for Onboarding if you want this feature to apply just to a unmarried on-premises phone.
-
Select Allow Activation Lawmaking via MRA and Crave Activation Lawmaking for Onboarding if you want to utilise Activation Onboarding for a single off-premises phone. If the phone is on-premises, information technology changes to Mobile and Remote Access way and uses the Throughway. If the phone cannot reach the Expressway, information technology does non annals until information technology is off premises.
For more information, see the post-obit documents:
-
Assistants Guide for Cisco Unified Communications Manager and IM and Presence Service, Release 12.0(i)
-
Mobile and Remote Access Through Cisco Throughway for Cisco Expressway X12.5 or after
Enable Autoregistration for Phones
The Cisco IP Phone requires Cisco Unified Communications Manager to handle call processing. See the documentation for your particular Cisco Unified Communications Manager release or the context-sensitive help in the Cisco Unified Communications Managing director Administration to ensure that Cisco Unified Communications Managing director is set up properly to manage the telephone and to properly route and process calls.
Before y'all install the Cisco IP Telephone, you must choose a method for adding phones to the Cisco Unified Communications Manager database.
By enabling autoregistration before you install the phones, you lot can:
-
Add phones without first gathering MAC addresses from the phones.
-
Automatically add a Cisco IP Phone to the Cisco Unified Communications Manager database when yous physically connect the phone to your IP telephony network. During autoregistration, Cisco Unified Communications Managing director assigns the next available sequential directory number to the phone.
-
Quickly enter phones into the Cisco Unified Communications Manager database and modify whatsoever settings, such as the directory numbers, from Cisco Unified Communications Manager.
-
Move autoregistered phones to new locations and assign them to different device pools without affecting their directory numbers.
Autoregistration is disabled past default. In some cases, you might not want to use autoregistration; for example, if y'all desire to assign a specific directory number to the telephone, or if you want to use a secure connection with Cisco Unified Communications Manager. For information about enabling autoregistration, meet the documentation for your particular Cisco Unified Communications Manager release. When you configure the cluster for mixed style through the Cisco CTL client, autoregistration is automatically disabled, however you tin can enable it. When you configure the cluster for nonsecure manner through the Cisco CTL client, autoregistration is not enabled automatically.
You lot tin can add phones with autoregistration and TAPS, the Tool for AutoRegistered Phones Support, without first gathering MAC addresses from phones.
TAPS works with the Bulk Administration Tool (BAT) to update a batch of phones that were already added to the Cisco Unified Communications Manager database with dummy MAC addresses. Use TAPS to update MAC addresses and to download predefined configurations for phones.
Cisco recommends that y'all use autoregistration and TAPS to add fewer than 100 phones to your network. To add more than 100 phones to your network, use the Majority Administration Tool (BAT).
To implement TAPS, you or the end user dials a TAPS directory number and follows vocalisation prompts. After the process is complete, the phone contains the directory number and other settings, and the phone is updated in Cisco Unified Communications Manager Administration with the correct MAC address.
Verify that autoregistration is enabled and is properly configured in Cisco Unified Communications Manager Administration before you connect whatsoever Cisco IP Phone to the network. For information about enabling and configuring autoregistration, come across the documentation for your item Cisco Unified Communications Managing director release.
Autoregistration must be enabled in Cisco Unified Communications Manager Assistants for TAPS to function.
Process
| Step 1 | In Cisco Unified Communications Manager Administration, click . |
| Step 2 | Click Find and select the required server. |
| Step 3 | In Machine-registration Information, configure these fields.
|
| Pace 4 | Uncheck the Auto-registration Disabled on this Cisco Unified Communications Director cheque box. |
| Footstep 5 | Click Save. |
| Step vi | Click Apply Config. |
Install Cisco IP Phone
After the phone connects to the network, the phone startup process begins, and the telephone registers with Cisco Unified Communications Manager. To terminate installing the telephone, configure the network settings on the telephone depending on whether y'all enable or disable DHCP service.
If you used autoregistration, you need to update the specific configuration information for the phone such as associating the phone with a user, changing the push button table, or directory number.
For data virtually installing accessories, run into Cisco IP Phone 7800 and 8800 Series Accessories Guide for Cisco Unified Communications Manager.
If you only accept one LAN cable at your desk-bound, y'all can plug your phone into the LAN with the SW port and then connect your computer into the PC port. For more information, see Share a Network Connection with Your Phone and Estimator.
You can also daisy chain 2 phones together. Connect the PC port of the first phone to the SW port of the second phone.
 Caution | Do not connect the SW and PC ports into the LAN. |
Procedure
| Step one | Cull the power source for the phone:
For more information, see Phone Ability Requirements. | ||
| Step two | Connect the handset to the handset port and press the cable into the channel in the phone. The wideband-capable handset is designed especially for use with a Cisco IP Phone. The handset includes a light strip that indicates incoming calls and waiting voice messages.
| ||
| Pace iii | Connect a headset or wireless headset. You lot tin add a headset later if y'all practice not connect one now. Press the cablevision into the cable channel.
| ||
| Step iv | Connect a directly-through Ethernet cable from the switch to the network port labeled x/100/m SW on the Cisco IP Phone. Each Cisco IP Phone ships with one Ethernet cable in the box. Apply Category 3, five, 5e, or 6 cabling for 10 Mbps connections; Category 5, 5e, or half-dozen for 100Mbps connections; and Category 5e or half-dozen for grand Mbps connections. For more data, run into Network and Computer Port Pinouts for guidelines. | ||
| Pace v | Connect a directly-through Ethernet cablevision from another network device, such equally a desktop figurer, to the reckoner port on the Cisco IP Phone. You lot tin connect another network device later on if you lot practise not connect one at present. Utilise Category 3, v, 5e, or six cabling for 10 Mbps connections; Category five, 5e, or 6 for 100Mbps connections; and Category 5e or 6 for 1000 Mbps connections. For more information, see Network and Computer Port Pinouts for guidelines. | ||
| Step 6 | If the phone is on a desk-bound, adjust the footstand. With a wall-mounted telephone, yous might need to accommodate the handset rest to ensure that the receiver cannot slip out of the cradle. | ||
| Step 7 | Monitor the telephone startup process. This step adds primary and secondary directory numbers and features that are associated with directory numbers to the telephone, and verifies that the phone is configured properly. | ||
| Step viii | If y'all are configuring the network settings on the phone, y'all can set up an IP address for the phone past either using DHCP or manually entering an IP address. Come across Configure Network Settings and Network Setup. | ||
| Step 9 | Upgrade the telephone to the current firmware image. Firmware upgrades over the WLAN interface may have longer than upgrading over the wired interface, depending on the quality and bandwidth of the wireless connexion. Some upgrades may take more than one hour. | ||
| Step 10 | Make calls with the Cisco IP Phone to verify that the phone and features work correctly. See the Cisco IP Phone 8800 Serial User Guide. | ||
| Footstep 11 | Provide data to finish users nearly how to utilise their phones and how to configure their telephone options. This step ensures that users take acceptable information to successfully use their Cisco IP Phones. |
Share a Network Connection with Your Phone and Computer
Both your telephone and your computer must connect to your network to function. If yous but accept ane Ethernet port, then your devices can share the network connection.
Earlier yous begin
Your ambassador must enable the PC port in Cisco Unified Communications Managing director before you can employ it.
Procedure
| Step 1 | Connect the telephone SW port to the LAN with an Ethernet cable. |
| Step 2 | Connect your computer to the phone PC port with an Ethernet cable. |
Set Upward Phone from Setup Menus
The Cisco IP Phone includes the following configuration menus:
-
Network Setup: Provides options for viewing and configuring network settings such as IPv4-only, IPv6-simply, WLAN, and Ethernet.
-
Ethernet Setup: The bill of fare items in this submenu provide configuration options to configure the Cisco IP Phone over an ethernet network.
-
WiFi Client Setup: The menu items in this submenu provide configuration options to configure the Cisco IP Phone with the wireless local area network (WLAN). Wi-Fi is only supported on Cisco IP Phone 8861 and 8865.
Note
The phone PC port is disabled when Wi-Fi is enabled on your phone.
-
IPv4 Setup and IPv6 Setup: These submenus of the Ethernet Setup carte du jour and of the WiFi Client Setup bill of fare provide additional network options.
-
Security Setup: Provides options for viewing and configuring security settings such as security mode, the trust list and 802.1X hallmark.
Earlier y'all tin can alter option settings on the Network Setup menu, you lot must unlock options for editing.
| Note | Y'all can control whether a phone has access to the Settings menu or to options on this carte du jour past using the Settings Access field in the Cisco Unified Communications Director Assistants Phone Configuration window. The Settings Access field accepts these values:
If you cannot access an option on the Ambassador Settings menu, check the Settings Admission field. |
Process
| Step i | Printing Applications |
| Step 2 | Select Admin settings. |
| Step three | Select Network setup or Security setup. |
| Step 4 | Enter your user ID and password, if required, and click Sign-In. |
| Footstep five | Perform 1 of these deportment to display the desired menu:
|
| Step 6 | To display a submenu, repeat footstep v. |
| Stride 7 | To exit a bill of fare, press Exit or the back arrow |
. Utilize a Phone Password
Yous tin can apply a password to the telephone. If you do, no changes tin be made to the administrative options on the phone without countersign entry on the Admin Settings telephone screen.
Process
| Footstep 1 | In Cisco Unified Communications Director Assistants, navigate to the Mutual Phone Profile Configuration window (). |
| Step 2 | Enter a password in the Local Phone Unlock Password pick. |
| Pace three | Apply the countersign to the mutual telephone profile that the phone uses. |
Text and Menu Entry from Phone
When you edit the value of an option setting, follow these guidelines:
-
Utilize the arrows on the navigation pad to highlight the field that y'all wish to edit, and then printing Select in the navigation pad to activate the field. Later on the field is activated, you lot tin enter values.
-
Use the keys on the keypad to enter numbers and letters.
-
To enter letters by using the keypad, utilize a corresponding number central. Press the central one or more times to display a particular letter. For example, press the 2 primal once for "a," twice quickly for "b," and 3 times quickly for "c." After you pause, the cursor automatically advances to permit you to enter the next letter.
-
Printing the pointer softkey
if you make a mistake. This softkey deletes the character to the left of the cursor. -
Printing Cancel before pressing Relieve to discard whatsoever changes that you made.
-
To enter an IP address, y'all enter values into four segments already divided for you. When y'all have finished inbound the leftmost digits before the showtime menses, apply the right pointer key to move to the next segment. The period that follows the leftmost digits is automatically inserted.
-
To enter a colon for an IPv6 accost, printing * on the keypad.
| Notation | The Cisco IP Phone provides several methods to reset or restore choice settings, if necessary. |
Enable the Wireless LAN on the Phone
Before you set up a wireless LAN, check to run across that your phone supports wireless use. The Cisco IP Phone 8861 and 8865 support a wireless LAN deployment. The Cisco IP Phone 8865NR does not support a wireless LAN.
Ensure that the Wi-Fi coverage in the location where the wireless LAN is deployed is suitable for transmitting voice packets.
If you have enabled the Wi-Fi connectivity for vox and you're using EAP-FAST or PEAP security mode, authenticate the Wi-Fi network with the WLAN Sign in application. WEP, PSK, and open security modes authenticate on the Wi-Fi network.
A fast-secure roaming method is recommended for Wi-Fi users.
| Notation | The phone PC port is disabled when Wi-Fi is enabled on your telephone. |
For complete configuration information, see the Cisco IP Telephone 8800 Wireless LAN Deployment Guide at this location:
http://www.cisco.com/c/en/us/support/collaboration-endpoints/unified-ip-phone-8800-series/products-implementation-design-guides-list.html
The Cisco IP Telephone 8800 Wireless LAN Deployment Guide includes the following configuration information:
-
Wireless network configuration
-
Wireless network configuration in Cisco Unified Communications Manager Administration
-
Wireless network configuration on the Cisco IP Telephone
Before you begin
Make sure that Wi-Fi is enabled on the phone, and the Ethernet cablevision is disconnected.
Procedure
| Step 1 | To enable the application, printing |
| Step 2 | Get to . |
| Step 3 | Enable the Wireless network. |
Prepare the Wireless LAN from Cisco Unified Communications Manager
In Cisco Unified Communications Manager Administration, yous must enable a parameter called "Wi-Fi" for the wireless Cisco IP Phone.
| Note | In the Telephone Configuration window in Cisco Unified Communications Manager Assistants (), use the wired-line MAC accost when you configure the MAC address. Cisco Unified Communications Manager registration does not utilize the wireless MAC address. |
Perform the following process in Cisco Unified Communications Manager Administration.
Process
| Step i | To enable the wireless LAN on a specific telephone, perform the post-obit steps:
|
| Step two | To enable wireless LAN for a group of phones, |
| Step 3 | To enable wireless LAN for all WLAN-capable phones in your network, |
Set Up Wireless LAN from Phone
Before the Cisco IP Phone can connect to the WLAN, yous must configure the network profile for the phone with the appropriate WLAN settings. You can apply the Network setup carte du jour on the phone to access the Wi-Fi client setup submenu and set up the WLAN configuration.
| Notation | The phone PC port is disabled when Wi-Fi is enabled on your phone. |
| Note | The Wi-Fi customer setup choice does non announced in the Network setup bill of fare when Wi-Fi is disabled on the Cisco Unified Communications Director. |
For additional information, run into Cisco IP Phone 8800 Series WLAN Deployment Guide, located here: http://www.cisco.com/c/en/u.s./support/collaboration-endpoints/unified-ip-phone-8800-serial/products-implementation-pattern-guides-list.html.
The User Modifiable field in the wireless LAN profile controls that ability of the user to configure security modes on the phone. When a user cannot change some of the fields, the fields display in gray.
Before you brainstorm
Procedure
| Footstep 1 | Press | ||||||||||||||||||
| Stride 2 | Select . | ||||||||||||||||||
| Footstep three | Fix upward the wireless configuration as described in the following table.
| ||||||||||||||||||
| Step 4 | Press Save to make changes or press Revert to discard the connection. |
Set the Number of WLAN Authentication Attempts
An hallmark request is a confirmation of the user's sign-in credentials. It occurs whenever a phone that has already joined a Wi-Fi network tries to reconnect to the Wi-Fi server. Examples include when a Wi-Fi session times out or a Wi-Fi connectedness is lost so reacquired.
You lot tin configure the number of times a Wi-Fi phone sends an hallmark asking to the Wi-Fi server. The default number of attempts is 2, but yous tin can set this parameter from 1 to three. If a phone fails the authentication, then the user is prompted to sign in again.
Yous tin can apply WLAN Authentication Attempts to individual phones, to a pool of phones, or to all the Wi-Fi phones in your network.
Procedure
| Stride 1 | In Cisco Unified Communications Director Administration, select and locate the phone. |
| Step 2 | Navigate to the Product Specific Configuration area and gear up the WLAN Authentication Attempts field. |
| Step 3 | Select Salve. |
| Step 4 | Select Utilize Config. |
| Stride v | Restart the phone. |
Enable WLAN Prompt Mode
Procedure
| Step 1 | In Cisco Unified Communications Manager Administration, select . |
| Pace 2 | Locate the phone that you demand to gear up upward. |
| Stride 3 | Navigate to the Product Specific Configuration area and set the WLAN Profile i Prompt Mode field to Enable. |
| Step 4 | Select Salvage. |
| Footstep 5 | Select Apply Config. |
| Step 6 | Restart the phone. |
Set up a Wi-Fi Profile using Cisco Unified Communications Manager
You can configure a Wi-Fi contour so assign the profile to the phones that support Wi-Fi. The profile contains the parameters required for phones to connect to the Cisco Unified Communications Manager with Wi-Fi. When you create and employ a Wi-Fi profile, yous or your users practice not demand to configure the wireless network for individual phones.
Wi-Fi profiles are supported on Cisco Unified Communications Manager Release 10.v(2) or afterward. EAP-FAST, PEAP-GTC, and PEAP-MSCHAPv2 are supported in Cisco Unified Communications Manager Release 10.0 and later. EAP-TLS is supported in Cisco Unified Communications Director Release 11.0 and later.
A Wi-Fi contour enables yous to prevent or limit changes to the Wi-Fi configuration on the phone by the user.
We recommend that you use a secure profile with TFTP encryption enabled to protect keys and passwords when you lot utilise a Wi-Fi profile.
When you set upwardly the phones to apply EAP-FAST, PEAP-MSCHAPv2, or PEAP-GTC authentication, your users need private user ids and passwords to sign into the telephone.
The phones just support one server certificate which tin be installed either with SCEP or the manual install method but not both methods. The phones don't support the TFTP method of document installation.
| Notation | Phones that employ Mobile and Remote Access through Expressway to connect to the Cisco Unified Communications Manager cannot use the Wi-Fi profile. Because you practise not take the SSID, authentication manner, and login credentials of the user'due south phone, you cannot configure a wireless LAN profile for their phone. |
Process
| Step 1 | In the Cisco Unified Communications Administration, select . | ||||
| Step two | Click Add New. | ||||
| Footstep three | In the Wireless LAN Contour Information section, set the parameters:
| ||||
| Step 4 | In the Wireless Settings section, set the parameters:
| ||||
| Step 5 | In the Authentications Settings section, fix the Authentication Method to one of these authentication methods: EAP-FAST, EAP-TLS, PEAP-MSCHAPv2, PEAP-GTC, PSK, WEP, and None. After you set this field, you may see extra fields that you need to gear up.
| ||||
| Step vi | Click Save. |
What to practice next
Use the WLAN Profile Grouping to a device puddle () or directly to the phone ().
Gear up a Wi-Fi Grouping using Cisco Unified Communications Manager
Yous can create a wireless LAN profile grouping and add any wireless LAN profile to this grouping. The profile group can then exist assigned to the phone when you set upward the telephone.
Process
| Step 1 | In Cisco Unified Communications Administration, select . Y'all tin also define a wireless LAN profile group from . |
| Step 2 | Click Add New. |
| Stride iii | In the Wireless LAN Contour Group Data section, enter a group name and description. |
| Stride 4 | In the Profiles for this Wireless LAN Contour Group section, select an available profile from the Available Profiles list and motility the selected profile to the Selected Profiles list. When more that one wireless LAN profile is selected, the telephone uses only the get-go wireless LAN profile. |
| Step v | Click Salve. |
Configure Network Settings
Process
| Step 1 | Press Applications |
| Step 2 | To access the Network Settings carte, select . |
| Pace 3 | Prepare the fields equally described in Ethernet Setup Fields. |
| Footstep 4 | After you lot accept set the fields, select Apply and Save. |
| Stride 5 | Reboot the phone. |
. Ethernet Setup Fields
The Network Setup menu contains fields and submenus for IPv4 and IPv6. To change some of the fields, first disable DHCP.
Establishing a VPN connection overwrites the Ethernet data fields.
| Entry | Type | Description |
|---|---|---|
| IPv4 setup | Menu | Run across the IPv4 Fields section. This option displays simply when the phone is configured in IPv4-only way or in IPv4 and IPv6 mode. |
| IPv6 setup | Carte | See the "IPv6 Fields" section. |
| MAC Address | String | Unique Media Access Control (MAC) accost of the phone. Brandish only. Cannot configure. |
| Domain Name | String | Proper name of the Domain Name Organization (DNS) domain in which the phone resides. To change this field, plough off DHCP. |
| Operational VLAN ID | Auxiliary Virtual Local Expanse Network (VLAN) configured on a Cisco Catalyst switch of which the phone is a member. This setting is blank if the auxiliary VLAN or the Authoritative VLAN are configured. If the phone has not received an auxiliary VLAN, this selection indicates the Administrative VLAN. The phone doesn't inherit the Operational VLAN from Admin VLAN if Cisco Discovery Protocol or Link Level Discovery Protocol Media Endpoint Discovery is enabled. To assign a VLAN ID manually, employ the Admin VLAN ID pick. | |
| Admin VLAN ID | Auxiliary VLAN of which the phone is a member. Used only if the phone does not receive an auxiliary VLAN from the switch; otherwise, this value is ignored. | |
| PC VLAN | Allows the phone to interoperate with 3rd-party switches that practise not support a voice VLAN. The Admin VLAN ID option must be set earlier yous can change this option. | |
| SW port setup | Auto Negotiate m Full 100 Half 10 Half 10 Total | Speed and duplex of the network port. Valid values specify:
If the phone is connected to a switch, configure the switch port to the same speed as the telephone, or configure both to autonegotiate. Unlock network configuration options if you lot desire to edit this setting. If you change the setting of this option, you must change the PC Port Configuration option to the same setting. |
| PC port setup | Motorcar Negotiate grand Full 100 Half ten Half 10 Full | Speed and duplex of the Figurer (access) port. Valid values:
If the phone is continued to a switch, configure the port on the switch to the aforementioned speed as the phone, or configure both to autonegotiate. Unlock network configuration options if you want to modify this field. If y'all change the setting, you lot must modify the SW Port Configuration option to the same setting. To configure the setting on multiple phones simultaneously, enable Remote Port Configuration in the Enterprise Phone Configuration window (). If the ports are configured for Remote Port Configuration in Cisco Unified Communications Manager Administration, the data cannot be inverse on the telephone. |
IPv4 Fields
| Entry | Description | ||
|---|---|---|---|
| DHCP Enabled | Indicates whether the phone has DHCP enabled or disabled. When DHCP is enabled, the DHCP server assigns the phone an IP accost. When DHCP is disabled, the administrator must manually assign an IP address to the telephone. For more information, encounter Ready Phone to Use DHCP and Prepare Telephone to Not Utilise DHCP. | ||
| IP Address | Cyberspace Protocol (IP) address of the phone. If you assign an IP address with this option, you must also assign a subnet mask and default router. See the Subnet Mask and Default Router options in this table. | ||
| Subnet Mask | Subnet mask used by the telephone. | ||
| Default Router | Default router used by the phone. | ||
| DNS Server 1 DNS Server 2 DNS Server 3 | Primary Domain Proper name Arrangement (DNS) server (DNS Server 1) and optional backup DNS servers (DNS Server 2 and 3) that the phone uses. | ||
| Alternate TFTP | Indicates whether the phone is using an alternating TFTP server. | ||
| TFTP Server one | Primary Trivial File Transfer Protocol (TFTP) server that the phone uses. If y'all are not using DHCP in your network and you lot desire to modify this server, yous must use the TFTP Server 1 choice. If you lot set the Alternate TFTP selection to On, you lot must enter a nonzero value for the TFTP Server 1 option. If neither the primary TFTP server nor the backup TFTP server is listed in the CTL or ITL file on the phone, you must unlock the file before y'all can save changes to the TFTP Server i option. In this case, the phone deletes the file when you save changes to the TFTP Server one selection. A new CTL or ITL file downloads from the new TFTP Server 1 address. When the telephone looks for the TFTP server, the phone gives precedence to manually assigned TFTP servers, regardless of the protocol. If your configuration includes both IPv6 and IPv4 TFTP servers, the phone prioritizes the order that it looks for the TFTP server by giving priority to manually assigned IPv6 TFTP servers and IPv4 TFTP servers. The phone looks for the TFTP server in this guild:
| ||
| TFTP Server two | Optional fill-in TFTP server that the telephone uses if the chief TFTP server is unavailable. If neither the primary TFTP server nor the backup TFTP server is listed in the CTL or ITL file on the phone, you must unlock either of the files before you tin save changes to the TFTP Server 2 choice. In this case, the phone deletes either of the files when yous salve changes to the TFTP Server 2 option. A new CTL or ITL file downloads from the new TFTP Server ii accost. If you forget to unlock the CTL or ITL file, you can change the TFTP Server 2 accost in either file, and then erase them by pressing Erase from the Security Configuration menu. A new CTL or ITL file downloads from the new TFTP Server 2 address. When the telephone looks for the TFTP server, information technology gives precedence to manually assigned TFTP servers, regardless of the protocol. If your configuration includes both IPv6 and IPv4 TFTP servers, the phone prioritizes the lodge that it looks for the TFTP server past giving priority to manually assigned IPv6 TFTP servers and IPv4 TFTP servers. The phone looks for the TFTP server in the following club:
| ||
| BOOTP Server | Indicates whether the phone received the IP address from a BOOTP server rather than from a DHCP server. | ||
| DHCP Accost Released | Releases the IP accost that DHCP assigned. This field is editable if DHCP is enabled. If y'all wish to remove the phone from the VLAN and release the IP address for reassignment, set this option to Yes and press Apply. |
IPv6 Fields
-
IP Addressing Mode
-
IP Addressing Mode Preference for Signalling
If IPv6 is enabled in the Unified cluster, the default setting for IP addressing fashion is IPv4 and IPv6. In this addressing fashion, the phone acquires and uses i IPv4 address and one IPv6 address. It can utilise the IPv4 and the IPv6 address equally required for media. The phone uses either the IPv4 or IPv6 accost for call control signaling.
For more details virtually IPv6 deployment, see the IPv6 Deployment Guide for Cisco Collaboration Systems Release 12.0.
You set IPv6 from 1 of the post-obit menus:-
When Wi-Fi is disabled:
-
When Wi-Fi is enabled:
Utilise the phone keypad to enter or edit an IPv6 address. To enter a colon, press the asterisk (*) on the keypad. To enter hexadecimal digits a, b, and c, press ii on the keypad, scroll to select the required digit, and press Enter. To enter hexadecimal digits d, due east, and f, printing 3 on the keypad, scroll to select the required digit, and press Enter.
The following table describes the IPv6 related information found in the IPv6 carte.
| Entry | Default value | Clarification |
|---|---|---|
| DHCPv6 Enabled | Yes | Indicates the method that the phone uses to go the IPv6-merely address. When DHCPv6 is enabled, the phone gets the IPv6 address either from DHCPv6 server or from SLAAC past RA sent past the IPv6-enabled router. And if DHCPv6 is disabled, the phone will not have whatever stateful (from DHCPv6 server) or stateless (from SLAAC) IPv6 address. |
| IPv6 Address | :: | Displays the current IPv6-only address of the telephone or allows the user to enter a new IPv6 address.
If the IP address is assigned with this selection, you must also assign the IPv6 prefix length and the default router. |
| IPv6 Prefix Length | 0 | Displays the current prefix length for the subnet or allows the user to enter a new prefix length. The subnet prefix length is a decimal value from ane to 128. |
| IPv6 Default Router | :: | Displays the default router used by the phone or allows the user to enter a new IPv6-only default router. |
| IPv6 DNS Server 1 | :: | Displays the primary DNSv6 server used by the phone or allows the user to enter a new server. |
| IPv6 DNS Server ii | :: | Displays the secondary DNSv6 server used by the telephone or allows the user to set up a new secondary DNSv6 server. |
| IPv6 Alternate TFTP | No | Allows the user to enable the use of an alternate (secondary) IPv6 TFTP server. |
| IPv6 TFTP Server 1 | :: | Displays the principal IPv6 TFTP server used past the phone or allows the user to set a new primary TFTP server. |
| IPv6 TFTP Server 2 | :: | (Optional) Displays the secondary IPv6 TFTP server used if the main IPv6 TFTP server is unavailable or allows the user to set a new secondary TFTP server. |
| IPv6 Address Released | No | Allows the user to release IPv6-related information. |
Set Up Phone to Use DHCP
To enable DHCP and let the DHCP server to automatically assign an IP accost to the Cisco IP Phone and direct the phone to a TFTP server, perform these steps:
Process
| Footstep one | Press Applications | ||
| Step two | Choose . | ||
| Step 3 | To enable DHCP, prepare DHCP Enabled to Yeah. DHCP is enabled by default. | ||
| Step 4 | To use an alternate TFTP server, gear up Alternate TFTP Server to Yes, and enter the IP address for the TFTP Server.
| ||
| Step 5 | Press Apply, |
Set Up Phone to Not Use DHCP
When not using DHCP, you must configure the IP accost, subnet mask, TFTP server, and default router locally on the phone.
Procedure
| Stride 1 | Press Applications |
| Step 2 | Choose . |
| Footstep 3 | To disable DHCP and manually ready an IP accost:
|
| Step 4 | Printing Apply. |
Load Server
Load Server is used to optimize installation time for phone firmware upgrades and offload the WAN past storing images locally, which negates the need to traverse the WAN link for each phone upgrade.
Y'all tin set up the Load Server to another TFTP server IP address or name (other than the TFTP Server ane or TFTP Server 2) from which the phone firmware tin exist retrieved for phone upgrades. When the Load Server option is set, the phone contacts the designated server for the firmware upgrade.
| Note | A Load Server option allows y'all to specify an alternate TFTP server for phone upgrades but. The telephone continues to use TFTP Server i or TFTP Server 2 to obtain configuration files. The Load Server option does non provide direction of the process and of the files, such equally file transfer, compression, or deletion. |
The Load Server is configured from the Enterprise Phone Configuration window. From Cisco Unified Communications Manager Assistants, choose Device > Telephone >Enterprise Phone Configuration.
Phone Startup Verification
After the Cisco IP Phone has power continued to information technology, the telephone begins the startup diagnostic process past cycling through the following steps.
-
The Feature and Session buttons flash bister and then greenish in sequence during the diverse stages of bootup as the telephone checks the hardware.
-
The master screen displays Registering to Cisco Unified Communications Manager.
If the telephone completes these stages successfully, it has started up properly and the Select push stays lit until information technology is selected.
Configure Telephone Services for Users
You can give users access to Cisco IP Phone Services on the IP phone. You lot tin can also assign a push to unlike phone services. These services incorporate XML applications and Cisco-signed Java midlets that enable the display of interactive content with text and graphics on the telephone. The IP phone manages each service as a dissever application. Examples of services include local movie times, stock quotes, and conditions reports.
Before a user tin can access whatsoever service:
- Y'all must employ Cisco Unified Communications Manager Assistants to configure services that are non present by default.
- The user must subscribe to services by using the Cisco Unified Communications Self Care Portal. This spider web-based application provides a graphical user interface (GUI) for limited, stop-user configuration of IP phone applications. However, a user cannot subscribe to any service that you configure every bit an enterprise subscription.
For more than information, come across the documentation for your particular Cisco Unified Communications Manager release.
Before you prepare services, gather the URLs for the sites that you lot want to fix upward and verify that users tin access those sites from your corporate IP telephony network. This action is non applicable for the default services that Cisco provides.
Procedure
| Step 1 | In Cisco Unified Communications Manager Assistants, choose |
| Footstep 2 | Verify that your users can access the Cisco Unified Communications Self Care Portal, from which they tin can select and subscribe to configured services. Meet Self Care Portal Management for a summary of the information that you must provide to end users. |
Change a User's Phone Model
You or your user tin can change a user's phone model. The alter tin be required for a number of reasons, for instance:
-
You have updated your Cisco Unified Communications Manager (Unified CM) to a software version that doesn't support the phone model.
-
The user wants a different phone model from their electric current model.
-
The phone requires repair or replacement.
The Unified CM identifies the old telephone and uses the sometime phone's MAC address to identify the erstwhile phone configuration. The Unified CM copies the sometime phone configuration into the entry for the new phone. The new phone then has the same configuration as the old phone.
If you change an old phone with SCCP firmware to a model in the Cisco IP Phone 8800 Series, the new phone is configured for Session Line Fashion.
If the old telephone has a fundamental expansion model configured, the Unified CM copies the expansion module information to the new phone at the aforementioned time. When the user connects a compatible fundamental expansion module to the new telephone, the new expansion module gets the migrated expansion module information.
If the sometime phone has a cardinal expansion model configured and the new phone doesn't support an expansion module, the Unified CM doesn't re-create the expansion module information.
Limitation: If the quondam phone has more lines or line buttons than the new phone, the new phone doesn't take the extra lines or line buttons configured.
The phone reboots when the configuration is consummate.
Before you begin
Set up up your Cisco Unified Communications Manager according to the instructions in the Feature Configuration Guide for Cisco Unified Communications Managing director.
You need a new, unused phone that comes preinstalled with Firmware Release 12.8(ane) or later.
Procedure
| Step 1 | Ability off the old telephone. |
| Step 2 | Power on the new phone. |
| Step 3 | On the new phone, select Supercede an existing phone. |
| Step 4 | Enter the primary extension of the old telephone. |
| Step 5 | If the one-time phone had a Pivot assigned, enter the PIN. |
| Step six | Printing Submit. |
| Pace vii | If there is more than one device for the user, select the device to supercede and press Continue. |
Source: https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cuipph/8800-series/english/adminguide/P881_BK_C136782F_00_cisco-ip-phone-8800_series/P881_BK_C136782F_00_cisco-ip-phone-8811-8841_chapter_011.html
0 Response to "what protocols are required to register a cisco 8800 series ip phone in cucm"
Post a Comment